Performance Evaluation of Multi-Layer Barriers for Machine-Induced Low Frequency Noise Attenuation -- Planing Process on AISI S-1006, S-7 and S-4340, based on Johnson-Cook Model Using Numerical Technique -- An Analytical Study of Diametral Error in Simultaneous Turning Process -- Improvement of Electric Heater Design for Household Cooking Application in Developing Countries -- Embodiment of an Efficient Brown's Gas Compound Fuel Tank -- Automated Solar Photovoltaic Panel Cleaning/Cooling System using Air-water Mixture and Sustainable Solutions to Off-grid Electrification -- Design and fabrication of four way multi hacksaw cutting machine -- Adhesion strength of Plasma Sprayed Coatings-A Review -- An Experimental Studies on the Polymer Hybrid Composites- Effect of fibers on Characterization -- Design Analysis and Pressure Loss Optimization of Automobile Muffler -- Different Module for car parking system demonstrated using Hough Transform for smart city development -- Effect of Arrangement and Number of Water Mist Spray Nozzles on Air Humidity -- Vibration Condition Monitoring of Spur Gear Using Feature Extraction of EMD and Hilbert Huang Transform -- Comparative Study of PWM Technique for Switching Loss Reduction and Acoustic Noise Reduction in VSI fed Drives -- An Improved Genetic Algorithm for Production Planning and Scheduling Optimization Problem -- Automatic Calibration for Residential Water Meters by Using Artificial Vision -- "Hardware in The Loop" of a flow plant embedded in FPGA, for process control -- Error Diagnosis in Space Navigation Integration using Wavelet Multi Resolution Analysis with General Regression Neural Network -- Hydromagnetic squeeze film performance of two conducting longitudinally rough elliptical plates -- Performance and Emission Characteristics of Biodiesel from Rapeseed & Soybean in CI Engine -- A Practical approach to Camera Calibration for Part Alignment for Hybrid Additive Manufacturing using Computer Vision -- Development of a colour and orientation detection system for small part feeding -- Comparative analysis on battery used in Solar Refrigerated E-rickshaw in India -- “Application of Value Stream Mapping (VSM) in a Sewing Line for Improving Overall Equipment Effectiveness (OEE): A Case Study” -- CFD analysis to increase heat transfer in pipe with combined effect of circular perforated ring and twisted tape insert -- Study On Solar Parabolic Trough Collector With Different Copper Absorber Tubes -- Harmonic Analysis for Bidirectional Grid Connected Converter for Electrical Vehicle during Charging and Discharging Operations -- Effect of tribolayer on the sliding wear behavior of detonation sprayed Alumina-Titania coatings -- Development of Sustainable Cementitious Binder Utilizing Silicomanganese Fumes -- Review on Sliding wear of Ti6Al4V alloy concerning counterface and sliding conditions -- Hardness and Microstructure studies on the effect of Solution treated-age hardened Al-6082 Alloy -- Floating Photo Voltaic Thin Film Technology - A Review -- Effect of Ethanol fumigation on performance and combustion characteristics of Compression Ignition Engine fuelled with Used Cooking Oil Methyl Ester in dual fuel mode -- Estimation and Moderation of Harmonics in Distribution Systems -- Theoretical Evaluation of Energy Performance of a Vapour Compression Refrigeration System Using Sustainable Refrigerants -- Effect of Autofrettage on the properties of the Aluminum Cylinders -- Influence of Graphene and Tungsten Carbide Reinforcement on Tensile and Flexural strength of Glass Fiber Epoxy Composites -- Investigation of partial discharge due to copper spherical particle in power transformer under various oil flow models using CFD -- A high power high frequency isolated DC-power supply for electrical vehicle charging application -- Effect of Slicing thickness and Increment on the design of patient specific implant for Total Knee Replacement (TKR) using Magnetic Resonance Imaging (MRI) - A case study -- Microstructure and Hardness Behavior Sudy of Carbon Nanotube in Aluminium Nanocomposites -- Comparison of Electric field with and without corona ring for 66kV line insulator -- Experimental and FEA Simulation of Thermal-Fluid Interaction Between TIN Coated Tungsten Carbide Tool and Inconel-825 Workpiece -- The Effect of Recrystallization on Electrical Resistivity of Stir Casted SiCP/AA6061 Composite after Shot Peening -- Static Stress Analysis of WYE-Piece for penstock application -- Comparative Investigation on Gas Tungsten Arc Welding and Friction Stir Welding of Electrolytic Tough Pitch Copper Plates -- Synthesis and Characterisation of Functionally Graded Ceramic Material for Aerospace Applications -- CI Engine Characteristic Investigation by Application of Metal Based Additives with Biodiesel Blends -- Simulation of underground cable faults (defects) with the detection of partial discharge -- Comparison of CI Engine performance parameters and Emissions by varying designs of Intake Manifolds -- Variation of Time Lag, Decrement Factor and Inside Surface Temperature with Solar Optical Properties of Building Envelope in Different Climatic Zones of India -- Study On Tensile and Hardness Properties of Al7075 Alloy Reinforced With Graphite, Mica and E-Glass -- ANN based fault classification and section identification technique using superimposed currents for three-terminal transmission line -- An analytical investigation for combined pressure driven and electroosmotic flow without the Debye–Huckel approximation -- Addressing the Green tribology advancement, future development and challenges -- Effect of Drying Temperature to the Drying Characteristic, Morphology and Peak Viscosity of Traditionally Processed Sago Starch (Lemantak) -- Evaluating Mechanical Properties of Egg Shell and Coco Peat Reinforced Epoxy Composite -- Design Modification of Rear Axle Housing by Fatigue Failure Analysis -- Mixture Design using Low Cost Adsorbent Materials for Decolourisation of Biomethanated Distillery Spent Wash in Continuous Packed Bed Column -- Prediction of the WPPO Biodiesel Fuelled HCCI Engine Using Artificial Neural Networks -- Dimensional Analysis of Form Drilling parameters by Buckingham pi theorem and optimization of heat generation in Form drilling process by Taguchi -- Comparison of ductile, flexural, impact and hardness attributes of sisal fiber reinforced polyester composites -- Optimization of EDM Process Parameters using Standard Deviation and Multi-Objective Optimization on the basis of Simple Ratio Analysis (MOOSRA) -- Modeling and Simulation of Trans Z-source Inverter with Maximum Constant Boost PWM Control for Solar PV System -- Driver Drowsiness Monitoring System -- Detection and Control of Water Leakage in Pipelines and Taps Using Arduino Nano Microcontroller -- Smart Automated Processes for Bottle-filling Industry using PLC-SCADA System -- Effect of Stirring Speed During Casting on Mechanical Properties of Al-Si Based MMCs -- Exploration of Pillars of Industry 4.0 using Latent Semantic Analysis Technique -- An Overview of Different Topologies of DC-DC Bidirectional Converter for Different Applications -- An Approach to detect and classify defects in Cantilever Beams using Dynamic Mode Decomposition and Machine Learning -- Musculoskeletal Simulation and Analysis of Upper Limb Rehabilitation Device -- Fuzzy Regenerative Braking Strategy -- A New Framework for Secure utsourcing of Medical Data -- A Comprehensive View for Providing the Decision on Medicare data -- Predicting Cardiac-Arrhythmia Using QRS Detection and Multi-Layer Perceptron -- Full Length Driver Drowsiness Detection Model – Utilising Driver Specific Judging Parameters -- Enterprise Reporting Solution on Integrating Business Intelligence for Operational and Financial Data -- Accelerating The Classifier Training Using Various Boosting Schemes Within Cascades Of Boosted Ensembles (Cobes) -- Service Layer Security Architecture For Iot Using

Biometric Authentication And Cryptography Technique.

This book includes selected, high-quality papers presented at the International Conference on Intelligent Manufacturing and Energy Sustainability (ICIMES 2019) held at the Department of Mechanical Engineering, Malla Reddy College of Engineering & Technology (MRCET), Maisammaguda, Hyderabad, India, from 21 to 22 June 2019. It covers topics in the areas of automation, manufacturing technology and energy sustainability.